Main Crankshaft Bearing & Seal Kit - Honda Odyssey FL350R (1985) (USA/Japan Aftermarket or OEM NOS)
Fitment, Sourcing Quality & Bottom-End Rebuild Guidelines:
- Vehicle Compatibility: Engineered specifically for lower-end crankshaft rebuilds on the 342cc air-cooled two-stroke single in the 1985 Honda Odyssey FL350R.
- Available Kit Grades:
- Premium Aftermarket (USA / Japan Sourced): Sourced strictly from top-tier American and Japanese bearing and seal manufacturers—never low-grade budget imports. Built to deliver maximum high-RPM endurance, tighter dimensional tolerances, and reliable crankcase sealing.
- Genuine Honda OEM (NOS): Authentic New Old Stock factory Honda parts for collectors and concours-level restorations. Available in strictly limited quantities; once depleted, they are permanently discontinued.
- Proper Crankcase Bearing Installation: Never hammer directly on bearing races or use the crankshaft nut to pull bearings into tight crankcase bores. Use thermal expansion (warming clean crankcase halves evenly to ~200°F–225°F while chilling the bearings) or dedicated crankcase puller tools so bearings seat squarely without side-loading the races.
- Crank Seal Protection & Leak-Down Check: Two-stroke engines depend on airtight crankcase compression to transfer fuel/air charge cleanly into the cylinder. Always lubricate the inner seal lips with two-stroke oil or assembly grease and use a protective sleeve over sharp keyways/splines during installation. Perform a crankcase pressure and vacuum leak-down test after reassembly before starting the engine.
Main Crankshaft Bearing & Seal Kit (Honda Odyssey FL350R 1985)
Restore rock-solid bottom-end reliability and airtight primary crankcase compression to your 1985 Honda Odyssey FL350R with our complete Main Crankshaft Bearing & Seal Kit. Decades of high-RPM dune running, heat cycles, and storage moisture degrade original main bearings and harden rubber crankshaft oil seals. Worn main bearings introduce excessive crankshaft runout and vibration—leading to damaged ignition stators, uneven piston wear, and rapid seal failure—while dried or cracked crank seals draw in unmetered air that causes catastrophic lean seizures.
We refuse to compromise your 350cc bottom end with cheap, low-grade imports. Our Aftermarket Kit is sourced exclusively from premier American and Japanese bearing and seal manufacturers, giving you top-shelf metallurgical strength and high-RPM C3 thermal clearances built for hard off-road abuse. For purists and collectors restoring an original machine, we also offer strictly limited quantities of genuine Honda OEM New Old Stock (NOS) components.
Key Specifications & Features:
- Dedicated 1985 FL350R Fitment: Matched to exact factory inner/outer diameters and widths for the Honda Odyssey 350 crankcase bores and crankshaft journals.
- Zero Cheap Imports: Aftermarket kits feature strictly high-grade USA- and Japan-manufactured bearings and elastomer oil seals—never low-tier budget substitutes.
- High-RPM Two-Stroke Tolerances: Precision-ground chromium steel raceways and internal radial clearances engineered for high-temperature two-stroke expansion.
- Airtight Double-Lip Crank Seals: Fuel- and oil-resistant seals lock in primary crankcase pressure and prevent lean air leaks or moisture intrusion.
- Complete Lower-End Coverage: Includes both main crankshaft bearings and the required outer crankshaft seals for a complete bottom-end refresh.
Package Includes:
- (2) Main Crankshaft Bearings (Drive Side & Ignition Side)
- (1) Complete Set of Outer Crankshaft Oil Seals
Order Direct from Oddball ORV for Proven Quality & Fast Shipping
| Condition | New |
|---|---|
| ATV Make | Honda |
| ATV Model | FL350R |
| Height | 6 |
| Width | 6 |
| Depth | 6 |









